How DAF’s 1958 Variomatic used belts, centrifugal weights and engine vacuum instead of gears

The DAF Variomatic changed gear without a single gear. Introduced on the DAF 600 in 1958, it used V-belts running between cone-shaped pulleys. Centrifugal weights and engine vacuum then decided, moment by moment, how big those pulleys should be.

That made a tiny Dutch economy car something unusual for its day: a small car with a fully automatic transmission and no clutch pedal. It also put a continuously variable transmission, or CVT, into a regular production car.

The clever part is that nobody had to tell it when to shift. Engine speed, throttle position and the load on the car did all the work through a few springs, weights and air chambers.

The idea behind the DAF Variomatic

The DAF Variomatic belt drive under a DAF 46
Image Credit: m66roepers from Nederland – CC BY 2.0/Wiki Commons

The belt-and-cone idea was old even in 1958. According to DAF Club Nederland’s guide to how the Variomatic works, an American named H.C. Spaulding described an infinitely variable drive in 1897. It used a belt and two conical pulleys, and it was meant for a car. However, it never went into production.

A Frenchman named Fouillaron came closer. The club says his drive used two pulley pairs and a V-belt made of leather slices strung on a metal cord. It reached series production in 1900 and went into dozens of cars. Because the driver had to change the ratio by hand, though, it soon fell out of use on cars.

DAF’s version solved that by making the system run itself. The club says the transmission appeared “under the name Variomatic on the Daf 600 passenger car” in 1958.

Belts and cone-shaped pulleys

Each pulley in the Variomatic is really two discs facing each other, like a pair of shallow cones. One disc is fixed, while the other can slide along its shaft. When the discs squeeze together, the belt rides higher on the cone. When they spread apart, it drops lower.

The belt itself never changes length. That’s why, according to DAF Club Nederland, pushing the front discs together forces the belt deeper into the rear pulley, and the reverse is also true. As a result, one pulley grows while the other shrinks, and the ratio changes smoothly with no steps.

DAF used two of these drives. Bill Vance’s history of the Variomatic describes two identical reduction units, each with two variable-diameter pulleys and a cogged V-belt. Spur gears and swing axles then carried the power to the rear wheels.

Centrifugal weights do the upshifting

The front, or driving, pulleys take orders from the engine. According to Vance, engine vacuum and centrifugal weights control them. Meanwhile, the rear pulleys are spring-loaded to keep the belt tight.

The weights are the simple part. DAF Club Nederland says each movable front disc carries two pairs of hinged weights. As engine speed rises, they swing outward and press the disc toward its fixed partner. That squeezes the belt outward and raises the gearing.

On the rear side, a coil spring and a set of disc springs push back. If the front squeeze wins, the drive upshifts. If the engine slows and the rear springs win, it downshifts. When the two balance, the ratio simply holds.

Load matters, too. The club says more resistance, such as a hill, a headwind or a trailer, raises belt tension and pulls the drive toward a lower ratio. Less resistance lets it climb again.

Engine vacuum handles kick-down and braking

Weights alone would only react to engine speed, so DAF added vacuum from the inlet manifold. A diaphragm splits each movable front disc into an outer chamber and an inner chamber, DAF Club Nederland explains.

Vacuum in the outer chamber pulls the disc inward and helps an upshift. So, when you ease off the pedal while cruising, the drive slips into a taller “overdrive” ratio. At full throttle, by contrast, there is almost no vacuum, and the outer chamber is vented to outside air. That gives the kick-down effect when you floor it to pass.

Vacuum in the inner chamber does the opposite. When you brake toward a stop, it forces a full downshift, so the car is ready to pull away again. It also keeps engine speed up for engine braking on a long descent.

What the DAF Variomatic delivered on the road

Vance says the DAF 600 debuted at the 1958 Amsterdam Auto Show and went into production in 1959. Power came from a 590cc air-cooled flat-twin rated at 22 hp. The Variomatic stretched that small output across ratios from 20:1 for starting to 4.4:1 at highway speed.

It wasn’t quick. Vance quotes a 0-50 mph time of 41.5 seconds and a 54.5-mph top speed from Road & Track’s 1960 test. Still, the magazine found the transmission did what DAF promised, with smooth, clutchless driving. The one weak spot was weather, since snow or ice could foul the exposed belts.

The idea outlived DAF’s car business. DAF Club Nederland says Volvo later built the transmission under the name CVT. Vance adds that a later DAF 55 used an adapted Variomatic behind a water-cooled 1,100cc Renault four, and that Nissan and Honda have since brought CVTs into the mainstream.

More from Fast Lane Only

Bobby Clark Avatar