Jack Brabham won the 1966 Formula One World Championship in the Brabham BT19, a car that carried his own name. Its Repco V8 began as an aluminum Oldsmobile block that he bought for about £11. That cheap block took him to four straight Grand Prix wins and his third world title.
The timing was the whole story. For 1966, as a result of new rules, Formula One doubled its engine limit from 1.5 liters to 3 liters. Coventry Climax, with 40 Grand Prix wins behind it, had already refused to build an engine for the new rules. So Brabham’s young team needed a 3-liter engine from somewhere else.
Brabham already knew how to win, though. Earlier, he had taken back-to-back titles with Cooper in 1959 and 1960. Then he set up his own team with engineer Ron Tauranac, who designed the chassis while Brabham served as team manager, mechanic and driver.
An £11 block from a shelved GM project

At first, the engine was little more than a parts-bin find. According to Motor Sport magazine’s history of the Repco engine, its base was GM’s liner-less aluminum F85 V8, a project GM had shelved at huge cost. Brabham bought a trial dry-linered version for around £11. Then he shipped it to Repco in Melbourne. By comparison, the Institution of Mechanical Engineers calls it an Oldsmobile Jetfire V8 block. Either way, the price is the same in both accounts.
Repco was also an unlikely engine builder. The Australian firm made replacement parts. Even so, its chief engineer, Frank Hallam, persuaded the board to back the racing program. However, the stock block had a problem. Its pushrod valvetrain, with the camshaft in the vee, wasn’t suited to a high-revving race engine.
That’s where Phil Irving came in. Born in Melbourne in 1904, he had previously been chief engineer at the motorcycle makers Vincent, HRD and Velocette. As a result, Irving replaced the pushrods and the cam-in-block layout with his own two-valve heads and chain-driven single overhead camshafts. Motor Sport notes that the heads were mirrored, so one design fit either bank. His first prototype, a 2.5-liter for Australia’s Tasman Series, ran on carburetors in March 1965.
The Repco 620 V8 by the numbers
The 1966 race engine was called the Repco 620. In Repco’s naming, for example, the hundreds referred to the block and the tens to the heads. Motor Sport gives it as a 2,994 cc, 90-degree V8 that made 285 bhp at 8,000 rpm on Lucas fuel injection. On top of that, it weighed 330 lb, measured 21 inches across the heads and returned around 7 mpg.
Those figures weren’t class-leading for power. In fact, Autosport puts the initial output at 280 bhp at 7,500 rpm, “just shy of the V12 Ferrari.” Instead, the engine won on weight and simplicity. For example, Autosport gives the V8 as 144 kg, while BRM’s complex H16 weighed 252 kg.
The parts list was resourceful, too. Motor Sport says the engine used a lightened Laystall flat-plane crankshaft and Daimler V8 connecting rods, which Brabham sourced at £7 each. Just as important, the compact V8 was narrow enough to fit an existing chassis. That chassis was Tauranac’s steel spaceframe Brabham BT19, and later the BT20.
Four straight wins in a nine-race season
The BT19 showed its pace early. On 1 January 1966, it led the non-championship South African Grand Prix until a loose screw in the injection system stopped it 11 laps from the end. Then, on 14 May, Brabham won the International Trophy at Silverstone from pole, with John Surtees 7.4 seconds behind.
The championship season had nine rounds, and the official Formula 1 results for 1966 show the run that settled it. Brabham won the French Grand Prix at Reims on 3 July. After that came Britain on 16 July, the Netherlands on 24 July and Germany on 7 August. At the Nürburgring, Motor Sport says, he won by 44 seconds in the rain.
Reliability did the rest. The IMechE says the BT19 was less powerful than some rivals but “won out in reliability,” and it took three pole positions. By the Italian Grand Prix in September, Brabham had the title wrapped up. He later retired at Monza with an oil leak, but by then it didn’t matter. The final standings show Brabham on 42 points to Surtees’ 28, and the team also secured the constructors’ title at Watkins Glen.
A first for a driver’s own car
Reims carried extra weight, because Autosport calls it the first world championship Grand Prix win in a car bearing its driver’s name. The IMechE goes further, however. It says the BT19 “was, and remains, the only car to win the F1 World Championship with the same driver and constructor’s name.”
The recognition followed quickly. First, the National Museum of Australia records that Brabham received an OBE in 1966, the first race-car driver to be granted the honor. Later, he was knighted in 1979. Meanwhile, the Repco-Brabham partnership kept winning. In 1967, Repco’s next engine, the 740, made 325 to 330 bhp, according to Motor Sport. That year, team driver Denny Hulme took the drivers’ title, and the team won the constructors’ championship again. Still, the deal didn’t last. After the 1968 season, Brabham switched to Cosworth power.
Where the Brabham BT19 is now
Today the Brabham BT19 is a museum piece. In 2014, the Institution of Mechanical Engineers gave the car its Heritage Award, recognizing the engineering behind the £11 block and Repco’s V8. The IMechE’s 2024 photo shows the title-winning car on display at the National Sports Museum in Melbourne, the city where Repco built its engine.
More from Fast Lane Only





