How Mazda’s Skyactiv-X uses a spark plug to trigger diesel-style compression ignition in a gasoline engine

Mazda Skyactiv-X is a gasoline engine that lights most of its fuel the way a diesel does: by squeezing it until it ignites. The trick is that it still uses a spark plug. Mazda calls the system Spark Controlled Compression Ignition, or SPCCI, and the spark is what tells the rest of the charge when to go.

That sounds like a contradiction, so it helps to start with the two kinds of engine it borrows from. A normal gasoline engine fires its fuel with a spark. A diesel has no spark plugs at all; it compresses air so hard that fuel ignites on its own.

Engineers have long chased a gasoline engine that could do both. Mazda’s answer was to keep the spark, but give it a different job.

Why compression ignition is hard in a gasoline engine

The prize is efficiency. As IEEE Spectrum explained in 2018, a typical engine burns fuel and air in the chemically correct ratio, which engineers call lambda 1. A leaner mixture, with extra air, cuts fuel use and makes less nitrogen oxide pollution. However, a lean mixture is also harder to ignite with a spark.

Compression ignition solves that problem, at least on paper. Engineers call the pure version HCCI. In practice, it was hard to control. Mazda’s own 2017 technical briefing said HCCI worked only at low rpm and low load, and that switching in and out of spark ignition was difficult. As a result, Mazda said, HCCI had not reached the point where it could be used in commercial applications.

Mazda was not the first to try. IEEE Spectrum notes that GM and Mercedes-Benz both pursued HCCI engines and ran into problems moving between modes.

How Mazda Skyactiv-X uses its spark plug

Mazda Skyactiv-X keeps the spark plug firing all the time. According to Mazda’s 2017 technology press information, “a spark plug is now being used at all times.” That is the key difference from HCCI.

First, the engine spreads a very lean mixture through the combustion chamber. Then it keeps a slightly richer zone around the spark plug. Mazda’s own Skyactiv-X page says the engine “uses a spark to ignite only a small, dense amount of the fuel-air mix in the cylinder.”

That small flame does the real work. Mazda’s briefing says “an expanding fireball created by spark ignition provides the final push.” The fireball raises pressure and heat in the cylinder. Because the lean mixture is already squeezed close to its ignition point, the extra pressure makes the rest of it ignite on its own.

IEEE Spectrum put it neatly: “The spark doesn’t so much light the fire as help the fire to light itself.” In effect, the spark plug becomes a trigger for compression ignition rather than the main source of the burn.

Timing is the other half of the job. Mazda says SPCCI can control the spark plug’s ignition timing, and that lets the engine decide when compression ignition happens. It also lets the engine move between compression ignition and conventional spark ignition without the switching trouble that held HCCI back.

Compression, air and sensors

Skyactiv-X needs very high compression for this to work. When Mazda released the production specs in 2019, its engine table listed a 16.3:1 compression ratio, as Motor1 reported. By comparison, IEEE Spectrum gives about 10:1 for a conventional turbocharged gasoline engine.

The engine also needs lots of air. CAR magazine described a Roots-type supercharger that Mazda calls an “air pump,” used to force extra air into the cylinders. Mazda’s briefing simply calls it a high-response air supply that can deliver larger amounts of air. IEEE Spectrum adds that engineers introduce swirl in the cylinder to keep the richer zone near the plug apart from the lean charge around it.

Finally, Skyactiv-X watches every combustion event. IEEE Spectrum says sensors measure combustion pressure in each cylinder every time it fires. The engine computer then uses that data to adjust the next cycle. Mazda’s briefing describes the same in-cylinder sensor as a way to correct deviations in real time.

What Mazda claimed and what it built

Mazda promised big gains. Its Skyactiv-X page claims 10 to 30 percent more torque than the Skyactiv-G gasoline engine. It also claims fuel efficiency up to 20 to 30 percent better than Mazda’s gasoline engine of the time, and better fuel efficiency than the Skyactiv-D diesel. In addition, Mazda says the engine runs on regular gasoline.

The production engine arrived in the Mazda3. Motor1 reported in June 2019 that European buyers could order the 2.0-liter Skyactiv-X in the hatchback or sedan. Mazda’s release listed 180 PS (132 kW), and Motor1 gave 165 lb-ft of torque. A 24-volt mild-hybrid system came standard.

Efficiency was the headline figure. Motor1 says the six-speed manual, front-drive sedan rated 5.4 liters per 100 kilometers combined in the WLTP test. That works out to roughly 44 mpg.

North America was another matter. When Motor1 published those specs, Mazda’s statement said, “We are currently studying when to launch Skyactiv-X in North America.”

More from Fast Lane Only