5 tri-power engines we’d trust completely

Three two-barrel carburetors on one manifold look like trouble to a lot of people. In fact, a well-sorted Tri-Power V8 is one of the friendliest ways to feed a big engine. Most of the time it runs on the center carburetor alone, and the outer two only join the party when you mean it. These are our picks, five triple-carb engines we’d happily drive anywhere, from Pontiac, Ford, Chevrolet and Mopar.

1. 1964 Pontiac GTO 389 Tri-Power V8

A 1964 Pontiac GTO 389 Tri-Power V8
Image Credit: Stephen Foskett – CC BY-SA 3.0/Wiki Commons

The 1964 GTO’s base 389 used a four-barrel and made 325 horsepower. Order Tri-Power, and the rating rose to 348. About 8,250 of the 32,450 GTOs sold that year had it. We trust it because only the center carburetor handles starting and low speeds. Meanwhile, the front and rear units carry no choke or idle circuit at all, just main and accelerator-pump circuits. With fewer parts to go wrong, the setup has less to fuss over.

2. Ford 406 Tri-Power V8

A Ford 406 Tri-Power V8
Image Credit: Morven – CC BY-SA 3.0/Wiki Commons

Ford built the 406 for only two years, 1962 and 1963, before it gave way to the 427. Ford bored the 390 out to 4.13 inches, which needed a new block with thicker walls. Then racing tests led to cross-bolted main caps, bolted through the sides of the block so they couldn’t walk under load. With three two-barrels, the 406 made 405 horsepower at 5,800 rpm and 448 lb-ft. A short life, then, but a stout bottom end, and that’s what earns our trust.

3. 1960 Chevrolet Impala 348 Tri-Power

A 1960 Chevrolet Impala 348 Tri-Power
Image Credit: Michel Curi – CC BY 2.0/Wiki Commons

Chevrolet’s 348 started life as a truck engine, and it kept working in big trucks through 1964. That’s a good sign for anyone who wants an engine that shrugs off abuse. It also had an odd design. Its combustion chamber sat in the cylinder, formed by an angled deck and a crowned piston, rather than in the head. For 1960, the high-output Tri-Power 348 made 335 horsepower. Chevrolet then replaced the 348 with the 409 as its top engine in 1961, the last year for the 348 in cars.

4. Pontiac 421 Tri-Power V8

A Pontiac 421 Tri-Power V8
Image Credit: Mr.choppers – CC BY-SA 3.0/Wiki Commons

Pontiac put Tri-Power on several sizes of V8, and the 421 was the biggest. For 1963, the street 421 Tri-Power HO used a hotter cam and iron exhaust manifolds to reach 370 horsepower. Later, the 1965 and 1966 versions carried a 356-horsepower rating. We’d trust one because its Rochester two-barrels are common GM pieces. That family of carburetors went on tens of millions of GM cars through 1978. Our look at the 421 Tri-Power covers its collector side, and this piece explains how the setup works. Pontiac dropped Tri-Power after 1966 and switched to the Quadrajet four-barrel for 1967.

5. 1970 Dodge Challenger R/T 440 Six Pack V8

A 1970 Dodge Challenger R/T 440 Six Pack V8
Image Credit: Stephen Foskett – CC BY-SA 3.0/Wiki Commons

Dodge called it the 440 Six Pack, while Plymouth badged the same engine the 440 6-BBL. Either way, it fed a 440-cubic-inch raised-block V8 through three Holley two-barrels. The rating was 390 horsepower at 4,700 rpm and 490 lb-ft at 3,200 rpm. That torque arrives low, so the engine never needs to be wrung out to feel strong. As a result, it’s the one we’d trust for long highway days. Our story on how the Plymouth 440 Six Pack became collector gold covers its sister. For 1971, its final year, Chrysler rated it at 385 horsepower.

More from Fast Lane Only

Bobby Clark Avatar