Chrysler put its first six-cylinder engine into the 1924 B-70, and the company has rarely been without one since. A Chrysler six has powered Plymouth sedans, Dodge trucks, farm tractors, Australian muscle cars and millions of family minivans.
Most of these engines never chased headlines. Instead, they earned their keep through long production runs, simple layouts and a habit of running long after the warranty ran out. Some stayed in production for decades. Others went on to work in welders, pumps and combines long after their cars were gone.
These are our picks: eight Chrysler six-cylinder engines, inline and V6, that seem so durable they’re nearly impossible to kill. The durability verdict is our opinion. However, the years, outputs and production figures come from engine histories, period ratings and the maker’s own announcements, linked in the entries.
1. 1951 Plymouth Cranbrook flathead six

Lift the hood of a 1951 Plymouth and you find about as plain an engine as Detroit ever built. It is an L-head inline six, with the valves in the block and nothing fancy above them. According to Mac’s Motor City Garage’s history of the engine, this family “faithfully served millions of Plymouth and Dodge owners from 1933 to 1959.”
Its roots go back to the 1924 B-70, Chrysler’s first production six, which displaced 201 cubic inches and made 68 hp. The first Plymouth version of 1933 displaced 189.8 cubic inches and made 70 hp at 3,600 rpm. Over the years, Chrysler stretched and tuned it. The final 230-cubic-inch Plymouth six developed 132 hp at the same engine speed. Remarkably, it never switched to hydraulic valve lifters during its whole life.
That simplicity is the point, in our view. There is little to break, and the engine is happy at low revs. If you want to see why vintage flatheads are making a comeback, a running Cranbrook six is a good place to start. Plymouth finally retired it for 1960, when the all-new Slant Six arrived.
2. 1946 Dodge D24C 230 flathead six

Dodge used the bigger 230-cubic-inch flathead from the 1942 D22 series. It then carried on in post-war cars such as the 1946 D24C sedan. The 230 shared its basic design with a whole family of Chrysler L-head sixes. That family went far beyond passenger cars.
For example, a 201-cubic-inch Chrysler six powered the Massey-Harris 101 tractor from 1938, and a 218 replaced it in 1940. A 242-cubic-inch Chrysler six also went into the Massey-Harris 201 Super until 1942. During World War II, the 251-cubic-inch version formed the basis of the Chrysler A57 multibank tank engine. Then, after the cars moved on, the flathead stayed in production until the early 1970s for industrial and agricultural work. Its last automotive job came in the 1968 Dodge Power Wagon WM300.
We’d argue that few engine families have been trusted with such different jobs. A family sedan, a farm tractor and a wartime tank all leaned on the same simple side-valve idea. As a result, a 1946 Dodge with a healthy 230 feels like a car built to be used, not babied. That’s exactly why we picked it.
3. 1968 Plymouth Valiant Slant Six

The Slant Six began on what Mac’s Motor City Garage calls “a clean sheet of paper,” with Willem Weertman leading the design. Engineers laid the cylinders over 30 degrees to the right. That lowered the hood line and moved the water pump beside the block, which made the engine about four inches shorter.
For 1960, the 170-cubic-inch version made 101 hp and the 225 made 145 hp. By 1968, the 170 carried a 115 hp rating, according to the Valiant owners’ engine table. Meanwhile, the toughness came from basic choices: four main bearings, a deep-skirted block and a short, stiff crankshaft. Solid lifters stayed until hydraulic ones arrived in 1981. Not every experiment worked, though, since the 50,000-plus aluminium-block 225s of 1961 to 1963 were prone to liner separation.
Chrysler kept it in cars until 1983 and in trucks until 1987. Even then, it carried on in marine, industrial and farm use until 1991, turning welders, combines and irrigation pumps. In our opinion, that is the definition of an engine that refuses to quit. We’ve also covered how the Slant Six earned that reputation before.
4. 1970 Chrysler Australia Hemi-6 245

Australia got its own Chrysler six in the 1970 VG Valiant. Engineers in Highland Park, Michigan, designed it for high output and light weight, partly to meet Australian local-content rules. According to Motales’ history of the “Kangaroo Six”, Chrysler Australia chose hemispherical heads, and engineer R. Dean Engle proposed canting the valves for better airflow.
The first 245-cubic-inch version, with a one-barrel carburettor, made 165 hp and 235 lb-ft. By comparison, the American 225 Slant Six of the day made 145 hp. Smaller 215 and larger 265 versions followed for 1971, and the 265 was a bored 245 rather than a stroked one. Chrysler Australia had built its first fully local Valiant, the AP5, by mid-1963. The Hemi-6 gave that home-grown car its own engine.
Durability did not come for free. Early endurance runs failed after about ten hours, partly because of the spark plugs. Once Chrysler fitted the coldest plugs available, the engine completed a 60-hour endurance schedule. In our view, that kind of development work is exactly what you want behind a six that seems hard to kill. The engine never reached showrooms outside Australia, New Zealand and Africa, which keeps it a curiosity for most American fans.
5. 1972 Chrysler Australia Hemi-6 Six Pack

The Six Pack turned the family sedan engine into a muscle car motor. Chrysler Australia bolted three 45 mm DCOE dual-throat Weber carburettors onto the 265-cubic-inch six. As Hagerty’s look at the Hemi Six explains, the E37 version made 248 hp, and the E38 lifted that to 280 hp.
Then came the E49 for 1972. With compression raised to 10:1, it made 302 hp and 320 lb-ft, all from six cylinders. Period tests quoted 0 to 60 mph in 6.1 seconds and a quarter mile in 14.4 seconds. By comparison, the E38 ran the quarter in roughly 14.4 to 14.8 seconds. A regular 265 in a Charger R/T made 218 hp. However, Hagerty puts E49 production at only 150 to 200 engines in its single model year.
Chrysler offered the Weber setup on the Charger R/T through 1973 before dropping it. We like the Six Pack because it proved the same basic engine could survive serious tuning, not just gentle family use. With so few E49s built, it’s the version we’d most like to hear on full song.
6. 2007 Chrysler Town & Country 3.3 V6

The first production 3.3 came off the line in Trenton, Michigan, on May 1, 1989, for the 1990 cars and minivans. Chrysler’s leaders kept pushrods while rivals moved to overhead cams, citing low cost and simplicity. The engine also used a cast-iron block with aluminium heads. According to Mopar history site Motales, it had the first “beehive” valve springs in any production car.
That simple layout gave a broad torque curve. More than 90% of peak torque arrived between 1,600 and 4,400 rpm, which suits a loaded minivan. From 2001 to 2010, the 3.3 made 180 hp, so this 2007 Town & Country carries the strongest version. If you want the bigger picture on why minivans became the family road trip vehicle, this engine is a big part of the story.
Chrysler built 5,076,603 of the 3.3 before it ended in 2010. Five million engines in family vans is a lot of school runs and road trips, in our opinion. If you’re shopping for an older Chrysler van, a well-serviced 3.3 is the drivetrain we’d look for first.
7. 1993 Chrysler Imperial 3.8 V6

The 3.8 grew out of the 3.3 when Chrysler lengthened the stroke, and it joined the range in 1991. In its first year, Motales notes, it had the same horsepower as the 3.3 but 15% more torque. That made it better at moving heavy cars, even if it felt less eager at high revs. Later tuning pushed the 3.8 to 215 hp from 2001 to 2007, which shows how much room the basic design had.
It first went into the Chrysler Imperial, the New Yorker and the Dodge Dynasty. In the 1991 to 1993 Imperial, it carried a rating of 150 hp. That was modest, but the extra torque suited a big luxury sedan cruising on the interstate.
Its long life is the best evidence for our pick. Chrysler later fitted the 3.8 to minivans from 1994, then gave it a new home in the 2007 to 2011 Jeep Wrangler. Trenton kept building it until May 2011, a year after the 3.3 ended. Together, the two engines ran for 22 years. We think a clean 1993 Imperial is the most comfortable way to enjoy one today.
8. 2018 Dodge Grand Caravan 3.6 Pentastar V6

The Pentastar replaced pushrods with an aluminium block, twin overhead cams per bank and 24 valves. Chrysler showed it at the New York auto show in April 2009, and production started in 2010. In the Grand Caravan, the 3,604 cc engine made 283 bhp at 6,400 rpm and 260 lb-ft at 4,800 rpm. It uses a 96 mm bore and an 83 mm stroke. The company builds it at its Dundee, Trenton and Saltillo South engine plants.
The Grand Caravan used the 3.6 from 2011 to 2020, so a 2018 van sits late in that run. Chrysler also fitted it to cars, SUVs and pickup trucks. That spread across so many vehicle types helps explain the big numbers that followed.
In February 2019, the company’s own blog celebrated the 10-millionth Pentastar V6. By then, the engine had also collected six Wards 10 Best Engines awards. In our view, that combination of volume and recognition makes the Pentastar the modern heir to the Slant Six. Ten million engines built in under a decade is the figure that tells the story.
More from Fast Lane Only





